Derek Posted March 3, 2003 Posted March 3, 2003 Got two full days in this weekend and wife is still talking to me. Planets must have been 'just right'. Quote
Frank Hagan Posted March 3, 2003 Posted March 3, 2003 Looking really good, Derek! I noticed you didn't cut the holes in the forward bulkhead, and I was trying to think why they are there. They do allow you to put longer things in the cabin, but there isn't much you would have on board that couldn't fit in the space between that bulkhead and the portion under the seats that is accessible from the cabin. And it might make it look nicer without the holes. Quote
High C Posted March 3, 2003 Posted March 3, 2003 The holes in that bulkhead also serve to ventilate the forepeak space. Every cavity in the boat should be ventilated to prevent meldew and rot in an enclosed space. The area behind the seats, too. It would look nice and ventilate well to install a couple of vents, or grates in that bulkhead. It also may be handy sometimes to be able to reach in there to get something from inside the cabin without going up on deck. My Weekender Site: www.jtservices.net/boat.htm Quote
Derek Posted March 3, 2003 Author Posted March 3, 2003 Good point High C. Actually, I did not want the holes that were spec'd on the plans, and was considering cutting in an opening for one or two 5" or 6" deck plates. But the grating idea is pretty good as well. Will have to toss that one around for awhile. I had also seen a couple of mods out there where the builder use the cutout to make a door for the opening and that was a consideration also. Quote
Stuart Benbow Posted March 3, 2003 Posted March 3, 2003 What I've done so far is to cut the starboard hole per plans, and left the port side for later. I plan to mount a marine stereo there inside some sort of marine electronics box that I've seen in various parts catalogs. I may put the circuit panel there as well, but I'm not sure. Quote
High C Posted March 3, 2003 Posted March 3, 2003 Yes, a door would be great, but bear in my how important that bulkhead is in terms of structure. It keeps the mast from breaking loose! I'd keep the cutouts no larger than those in the plans, and similarly located. Quote
capt jake Posted March 4, 2003 Posted March 4, 2003 Just remember, you can't get a standard router to those edges after the fact. Better to do that ahead of time, if you cut out the holes. Route and sand as much as possible 'before' assembly!! Quote
T. Nelson Surbrook Posted March 4, 2003 Posted March 4, 2003 Nice job! This is looking good and I like seeing another Washington builder. I wonder how many builders we have in this fine state now...We should have plenty to have a get together this summer and have some sailing fun. Paul had the ldea of having a get together at Anacortes a couple of years ago and I think it would still be a good plan. I would be up for taking a trip to the coast for some sailing fun. I like the modification to the stem for attaching the bits. Keep up the fine work and before long you will have her in the water. Quote
Barry Pyeatt Posted March 5, 2003 Posted March 5, 2003 Looking good at this stage Derek. I would add a huge "AMEN" to Jakes statement about routing and sanding before you assemble these. Fill and seal the edges and prime first as well if possible. Just mask off the areas where you are attaching the mast box first. You'll really appreciate it later on when it is really tough to get to. :wink: Quote
Derek Posted March 5, 2003 Author Posted March 5, 2003 Thanks All for the tips, not a one goes to waste. Question - I had seen, can't recall where off hand, a builder that had applied 5200 I believe to all points where stringer meets ply, joiner meets ply and so on. Overkill or a good idea? Quote
Frank Hagan Posted March 5, 2003 Posted March 5, 2003 Thanks All for the tips' date=' not a one goes to waste. Question - I had seen, can't recall where off hand, a builder that had applied 5200 I believe to all points where stringer meets ply, joiner meets ply and so on. Overkill or a good idea?[/quote'] The Stevensons have that in the video ... 5200 along all those points. I did it, and I think it took 3 of the 11 ounce tubes (and two tee shirts ... that stuff is relentless!) Quote
Pat Mellema Posted March 6, 2003 Posted March 6, 2003 I used 5200 on all the joints in Sanddragon they are all joints I don't want to come apart. The 5200 does make a good seal on the joints. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.