Jump to content

Recommended Posts


Posted

Very Nice Rob,

Thanks for sharing

Is that a CS17 or CS20 ?

I'm currently trying to decide between 17 or 20 ft Core Sound design to build for sailing Moreton Bay, and other Queensland esturaries.

Cheers

Mark

Posted

Get the 20 in my opinion.

2 blokes and gear, fits well, I really think the 17 would be too small for somewhere like Hervey Bay. We have had some hairy trips up there and the 20 handled it really well.

You are welcome to come and see ours. We are in Lennox Head

Rob

0434 004 895

Posted

Thanks Rob

I think I will take your advice and go with the CS 20.

I have not seen a CS in the flesh yet, so may take you up on the offer. I used to windsurf Lennox and Flatrock years ago, very nice place.

Cheers

Mark

Posted

Hi Rob

Where in the bay did you go? In particular where were you camping?

I'm building a Cs17 (#165)- glued on the gunwale rubbing strips on Sunday.

Peter HK

Posted

Thanks for the video. I have noticed your boat among the picture collection that Carla sends out with the plans, and it is indeed a beautiful craft. Was it built exactly to spec, ie, are the side decks "standard," or wider than the plans call for? Also, since you've apparently had her sailing for 4 or 5 years, how have things held up? Any notable maintenance or repair issues? 

Posted

sorry about the delay...

How has the boat held up... Good really, except when we hit the corner of a pontoon and punched a hole. Also when I towed it out from under my house and knocked the transom off because I left the engine on the transom and it hit the bottom of the bathroom.

The finishes have been good and bad. The waterbased epoxy paint was a matt finish and was never much good in places. Eric had a lot of trouble spraying it. It also does not bond well to the old coating inside.. The same with the waterbased clear finish.

I am sure the vendor/maker would tell me why it should have worked but we have tried and it has been hard.

I have just cracked the mizzen floor fitting which is made from timber and epoxied. Suspect the mast rocking on the gallows whilst trailing on the road. Am going to put a stainless fitting in there instead.

Otherwise it is good.

The boat is nearly standard, Eric curved the seat lockers to follow the line of the coaming better and we raised the aft deck a bit to allow more storage, but not all the way in the plans. Happy with that.

The music was  a Neil Finn song .. 6 Months in a Leaky Boat sung by Little Birdy... Album... She Will Have Her Way

We launched at Southport and had the first night at Jumpin Pin Bar and then the next two nights at Caniapa Point on N Straddy .. We planned to go to Manly on the last day but the wind which had been on the nose for most of the weekend gave up the ghost so we motored half way home and got the car.

Rob

Posted

Nice video Rob.

What stands out to me (other than the cool music) is how fast the boat is moving relative to what appears to be relatively light wind. That looks to be 5 knots plus boat speed in light air and not even working hard (dead level and sheets hanging loose).

If that is typical for these boats and rigs, time for me to upgrade to a cat ketch! :)

Posted
We launched at Southport and had the first night at Jumpin Pin Bar and then the next two nights at Caniapa Point on N Straddy

Even though I live here I haven't been that way for a few years- always trying to find somewhere further away/more exotic. Just goes to show how silly human nature is.

Here are a couple of photos from my last trip that way...the first is at the Bedroom near Jumpin Pin (showing a Wallaby on Pandanus Island) and the second the beach at Canaipa.

post-1007-129497677184_thumb.jpg

post-1007-12949767719_thumb.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.