Jump to content

Normal? S10n bow after going 3D.


mjshp
 Share

Recommended Posts

Spindrift 10n, Hull 933 started going 3D today. And I have a few questions I hope some of the more able of you can answer.

Frist off, 933 is a kit from B&B, the foreward bluk head is in and fits great, the nesting bulkhead and transome will go in tomorrow.

Question 1:

The keel and chines are wired and because if the keyed chine, they line up great, but at the bow, the lower section of the hull--below the chine--is a bit proud (1-2 layers of the ply are a sticking out of the seam. See the photo below. The problem is only with the first 2 keys of the chine, You can see the proud part under the frist wire tie.

If these need to be pulled in, any suggetions? Or should the just be removed when I flip the boat over and round and tape all the ouside edges?

Question 2:

The mated, nesting blukheads. Should they be wired in? Screwed in? Glued in?

Question 3:

After the transom and nesting bulkhead are in ? Fillet and tape, then gunnels or gunnels then fillet and tape?

Thanks in advance for your help.\

Michael

post-2157-0-26512900-1329628788_thumb.jpg

Link to comment
Share on other sites


The gunwales should be at least clamped (if not glued) to the shear to pull the shape fair before you do the inside filleting & taping. Be sure to do both sides at the same time to keep the sides symmetrical. The transom & the bulkheads need to be wired in place to make sure everything fits the hull shape is fair.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

    • By Aleksandr Pasechnik
      I've had a few situations now where I'm in unsteady waters and want to be able to switch my Spindrift 11N to rowing. I've added a topping lift (a simple single line from the top of the mast to the end of the boom) so that the boom doesn't drop into the boat when a release the halyard, but that's proving to be annoying still, since the lift is hard to adjust when there's a breeze and the boom is bouncing around. So now I'm thinking about adding a block to the top of the mast and running the topping lift down and cleating it off with the other control lines.
       
      Part of the goal here is to be able to quickly get the sail out of the way and out of trouble when I need to be rowing. So my theory is that if I add the lift, and then, when necessary, pull the boom way up above my head (30˚ or 45˚ up, perhaps?) then the sail is free to flop and flap about (maybe with some mainsheet tension to keep it towards the back of the boat) but I'd be able to row out of trouble. Is that wrong? Am I liable to end up with a sort of parachute way up in the air knocking my boat around?
       
      Last time I tried to bring the sail down while on the water, the zipper for the sleeve got stuck and then I was bouncing around, and then there was a pier wall, and that was a good 20 minutes of keeping Elsewhere off the wall and upright, pulling myself along to a dock. I'm wondering if a pullable toping lift in conjunction with some kind of line on the sleeve zipper pull would make it easier to get the sail down and out of the way in an emergency. I guess if I'm switching to oars for emergency purposes, I don't really care about getting the sail back up after I'm done rowing to a dock of some kind.
       
      So I guess the question is: how do folks disable, significantly depower, or douse the sleeved Spindrift sail on the water? Do I have to switch to a lashed or rail configuration for the sail? Would raising the sail clew without the ability to mess too much with the other sail controls (with the exception of maybe loosening the halyard and whatever the reefing line can do) make a very tippy boat?
       
      I guess I could also reach the outhaul and the attachment of the reefing line, usually. If I were to replace the bowline knots on their attachments to the boom with some kind of quicker-release knots or pins or something, I could let the whole sail fly free. Maybe add some way of bunching it up to the mast?
    • By Aleksandr Pasechnik
      tl;dr: Looking for learning resources for non-competitive dinghy sailing.
       
      Hiya folks! So I’ve pretty much finished my Spindrift 11N. Her name is Elsewhere and she is red and white and wonderful. I’m sailing on the Hudson River off Lower Manhattan (Pier 40 is home). The Hudson is fun! Salty, a little icky, and a lot ferry. We play chicken, me and the ferries and the party boats and the giant barges. Never a dull moment.
       
      I learned to sail and practiced on a 22-foot-ish bermuda rigged sloop on a quiet little “river” (more of a long lake, really). Elsewhere is much more skittish and “active”. And less forgiving of errors. Like getting the mainsheet caught on a life vest attachment during a tack. That got me in the water right quick, and the fire fighters dropping by to see what the fuss was about. I’m learning all about the nuances of downwind sailing on a boat without shrouds and how crucial line management and tidiness is.
       
      So the question: are there books or other learning resources for the “beginner” cat rigged dinghy sailor? Not particularly interested in racing, but looking to hone the craft of safe and confident sailing. (My heart rate is apparently consistently two to three times higher on the boat than on land =D )


    • By ForthBridge
      Hello everyone,
       
      I last posted on here a few years ago.  It's taken me sometime to convince my wife to give up the living room to an N11.
       
      My Spindrift N11 project is called South Queensferry Electron - in recognition of Donald Crowhurst's Teignmouth Electron - https://en.wikipedia.org/wiki/Donald_Crowhurst
       
      Following the usual 'messing-about' convention, here is my progress right up to when I found the courage to saw her in half - earlier today!
       
      Nidaplast is very flexible and I epoxied and peel plied each piece of the hull before assembly.  Bulkheads are carbon fibre and Nidaplast, three layups of biaxial cloth.  A diamond cutting wheel on a Dremmel made short work of trimming excess from the bulkheads and transom.
       
      The hull still needs finishing, as do the bulwarks.  Knees still to fit as well, that's the next job.
       
      So I realise that 6mm ply would have been the best route to go down.  However, prior to this build I had not worked with West Systems or carbon fibre before.  The SQE is a 'learning by doing' project in preparation for the retirement boat.
       
      I will update with more photos as work progresses.  I live in Scotland, the weather is getting colder and less conducive to epoxy use and, of course, I have to give the living room up for Christmas.  Progress might be slow!  However, with the hull complete I can cut out the rest of the Nidaplast components and get the sailing rig ready.
       
      Happy boat building to you all!
       
      Jim
       
       
       






    • By William
      For want of a decent local plywood supplier I will be building in 5mm nidacore honeycomb sandwich, carbon outside, vectran and glass inside. If I can get my hands on some affordable basalt fabric I am sure I will find a few panels for it to feature. It is certainly not going to be as enjoyable as building in wood but at least I will get to learn a few new skills along the way. A lighter boat is almost a guarantee, but that all depends on how many laminates will give me the impact toughness I require. 
       
      I do have a partial sheet of nice 6mm ply and will cut the transom, mast partners and a few other small parts from that.
       
      The nidacore sheets are 7ft x 4ft, which, as fortune would have it, is just long enough to cut the main hull panels from 3 sheets, one being halved and butt-joined to the full sheets just like the plans for plywood.
       
       
    • By Luke
      Hi everyone, this is my first post--I've been lurking here getting lots of good info as I build and finally have a few questions myself!
       
      By now the boat is 3D and wired together. The hull, bulkheads, and transom all seem to fit well, and the boat has no twist in it that I can discern. Measurements from the peak of the bow to the corners of the transom are 109" +/- an 1/8", and sighting down the centerline, the tips of the nesting bulkheads "disappear" below the transom at the same time.
       

       
      I've made a number of spanish windlasses to pull the sides together between the forward and mid bulkhead, to pull out the 1/2" gap between the bottom and the bottom of the nesting bulkheads, to pull the forward bulkhead forward onto its lines, and lastly to try to flatten the bottom seam between bulkheads slightly to close a gap in the bottom panels.
       
      The question is how much of a gap along the keel seam is acceptable? It goes from no gap at the transom and widens to about 1mm around the nesting bulkheads, and up to a maximum of about 3mm halfway between the forward and mid bulkheads. I think the epoxy fillets will cover it just fine, but I just want to make sure it's not a symptom of a larger problem.
       
      Also, the plans don't really give dimensions to make a breasthook or quarter knees--do I just make these to fit the shape of the hull as it stands now? The instructions say the breasthook (included with the kit I suppose) is important to ensure the bow takes the correct shape--so what gives? The sheer lines look nice.
       
      Lastly, I centered the kerf gap of the nesting bulkhead on the "center frame" lines running down the sides--is that correct?
       
      Thanks!
       
       
       
      Additional photos
       
      Looking aft:

       
       
      chine

       
      bow and gap

       
      forward bulkhead

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.