Chick Ludwig Posted March 18, 2022 Report Posted March 18, 2022 Just finished our new electric mini-boat. The plan is to build another so Debbie and I will each have one. Then try to promote them in our area and get a little messabout group going. Finally got the new mini in the water. All went well. Even the pup enjoyed the ride. Now I can start mini #2 and get the final plans drawn up. They'll be available to you guys soon. 100_0607.MOV 3 Quote
Chick Ludwig Posted April 2, 2022 Author Report Posted April 2, 2022 I'm now building electric mini-boat #2. It is the same hull as mini #1, but with some interior and decking changes. I'm also getting accurate measurements to make drawings so you can build your own. So here is Mini-boat #2 - post #1 These views show how the hull panels are stitched together and epoxy fillets applied between the wires. You could use electrical cable ties, but I prefer bailing wire because I can pull the panels tighter together. 1 Quote
Wommasehn Posted April 23, 2022 Report Posted April 23, 2022 Hi Chick, this looks really cute! Would you like, telling us a bit more about these mini-boats ? where and for what you plan to use them, what kind of motor etc? Stay healthy Tobias Quote
Chick Ludwig Posted April 25, 2022 Author Report Posted April 25, 2022 Wommasehn, Just mess around with them. We hope to get several other folks to build them so we can "cruise" together. If you look on YouTube, you'll see a lot about them. We use regular electric trolling motors that we modify with remote steering and peed controls. Quote
Hirilonde Posted April 25, 2022 Report Posted April 25, 2022 29 minutes ago, Chick Ludwig said: Wommasehn, Just mess around with them. Bah, Chick just wanted more boats to build. 1 Quote
Chick Ludwig Posted April 29, 2022 Author Report Posted April 29, 2022 On 4/25/2022 at 9:01 AM, Hirilonde said: Bah, Chick just wanted more boats to build. I'm afraid ya got THAT right! but, dang it if a bunch of "life" stuff hasn't gotten in the way. Got the seams taped and came to a screeching halt! Quote
Kennneee Posted May 1, 2022 Report Posted May 1, 2022 As the saying goes “life happens when you busy making other plans”. Hope YOUR plan can get back on track soon. 1 Quote
Chick Ludwig Posted May 23, 2022 Author Report Posted May 23, 2022 I bet y'all think I forgot about ya. Nope! Just haven't been able to work on the mini. Too much "life" going on. BUT---I finally have gotten a bit done! Added the 3/4" stiffening for the motor area of the transom, and the 1/2" x 3/4" sheer clamps. Also the little "fiddles" to keep the battery where it belongs. I'll be back soon with the next additions. 1 Quote
Chick Ludwig Posted May 27, 2022 Author Report Posted May 27, 2022 Mini-boat (#2 - after this post, I'll leave off the "#2") )Post #3 Today's main job was to make flotation boxes. Boat #1 didn't have them and could sink from the weight of the battery and motor. The pictures show them “tabbed” in place with a few dabs of hot-melt glue holding them until they can be poxy filleted. I need to poxy coat the insides first, They are only air tanks---no foam. While working on this step, the motor on my 6 inch belt sander burned up. Sparks and flames shot out! I called the part supplier for the sander. The motor is obsolete. They have one left for $400!!!! i found another sander on Craigslist for $130. Guess where I'm going this morning. Quote
Hirilonde Posted May 27, 2022 Report Posted May 27, 2022 I found aftermarket parts for my surface planer and RO sander from these guys. https://www.ereplacementparts.com/?source=gaws&gclid=CjwKCAjw7cGUBhA9EiwArBAvoiHWmR6WzF9NTnSUH8OIk7yLIGxtM8i9yAV_KL2CmhNkrBuW7l0bShoC-GUQAvD_BwE Quote
Chick Ludwig Posted May 28, 2022 Author Report Posted May 28, 2022 Thanks. I checked but they say the same thing. "No longer available" from them either. If it was, it would be $400. I bought the used Craftsman sander. It needs $35 worth of new bearings---already ordered. I think my old sander had been used by Noah when he built the Ark. 1 Quote
Chick Ludwig Posted June 4, 2022 Author Report Posted June 4, 2022 Mini-boat Post #4 (6-4-22) All of the outside “corners” have been glassed with 2 inch tape and then sanded to remove the ridges of the tape. The keels have been added. They are 3/4” wide and 1” deep. They worked well on boat #1 to help tracking and stiffen the 6mm bottom. The boat was flipped back upright and deck framing was added along with the motor well. I also made the steering drum and steering well, but you'll have to wait for the next post to see pictures of those. Quote
Chick Ludwig Posted June 7, 2022 Author Report Posted June 7, 2022 Mini-boat Post#4 (6-7-22) BACK AGAIN! But, not much has happened since last time. Two coats of poxy have been slopped on the inside of the hull. I even remembered to drill a drain hole. It goes through the center keel strip. The plug is a simple 3/8 inch “flip plug” from Lowe's. I told you I'd post pictures of the steering wheel and drum. They are on a ½ inch dowel. The next post should have them mounted. But first, I will sand the poxy and paint on a coat or two of varnish, so I may not be back for a few days. Gotta let the poxy cure good before sanding. Quote
Chick Ludwig Posted June 11, 2022 Author Report Posted June 11, 2022 Mini-boat Post #6 (6-11-22) The steering drum, pulleys, and “guide tubes” are in place. The steering cables will be led through fairleads through the deck after the deck is installed. The deck is roughed out and sitting in place. The openings for the cockpit, hatch, and motor well will be cut to fit after the deck is bonded down. Not shown is the deck lifted back off and poxy coated on the backside, and the interior of the hull varnished. Quote
Chick Ludwig Posted June 27, 2022 Author Report Posted June 27, 2022 Mini-boat Post #7 (6-27-22) Lots going on to keep me from the mini-boat project, but here's an update. The interior has been varnished---BUT... I used Rustoleum varnish over properly cleaned and sanded epoxy, but it wouldn't dry completely. Some varnishes are nor compatible with epoxy. I usually use Pettit Captain's varnish which is, but didn't have any, none available locally, and expensive to order and ship. I “cheaped out”. Ya think and old guy would know better! It was still tacky after several days!All I could do was add another coat on top of the tacky one. This works pretty well, but still takes a long time to dry. But finally it is done. The two coats that took so long have plenty of dust settled on/in them. I just ignore it. Maybe later I'll go back and sand it all and add another coat. Looks good from a few feet away. I dunno. Moving right along. The deck has been installed except for “doubling” around the cockpit sides. I also built a raised coaming around the hatch area behind the cockpit. Next project is the hatch. Also fairleads to lead the steering cables through the deck have been made and installed. And stern lifting handles. I didn't have them on boat #1 and they are needed. That's it for now. See ya next time with more exciting adventures in the mini-boat mini-saga! Quote
Hirilonde Posted June 27, 2022 Report Posted June 27, 2022 4 hours ago, Chick Ludwig said: The two coats that took so long have plenty of dust settled on/in them. I just ignore it. Maybe later I'll go back and sand it all and add another coat. Looks good from a few feet away. I dunno. It's called a non-skid surface. 1 Quote
Chick Ludwig Posted June 28, 2022 Author Report Posted June 28, 2022 17 hours ago, Hirilonde said: It's called a non-skid surface. Well, there's not THAT much dust. But it sure isn't a purty, slick surface, either. Quote
Chick Ludwig Posted July 1, 2022 Author Report Posted July 1, 2022 Mini-boat Post #8 (7-1-22) It's PICTURE DAY! First pic is of the steering cable coming though the fairleads. Next is of the boat so far. Then the hatch coaming, next two are of how the "doubler" is made to stiffen the edge of the cockpit. Then the hatch being assembled. Can't forget the bow handle! Steering attachment to the motor. Now it's time to modify the trolling motor for the remote PWM control unit. (Pulse width Modulation). First is how the wiring is on the handle of the motor after you remove the top of the control head of the trolling motor. These will be un-hooked. Last picture is showing how the shaft has been cut down. I used a tubing cutter. If you use a hack saw or saber saw, be careful to not hit the wires! The big wires, red/black and black are the power supply to the motor. They will be attached to the PWM motor terminals. The yellow and blue wires will be cut off and the ends stuffed down the tube. They are for the forward/reversing with and aren't needed because that will be done through the PWC. I'll show this all in the next post. Post #8 (7-1-22) 1 Quote
Chick Ludwig Posted July 8, 2022 Author Report Posted July 8, 2022 Mini-boat Post #9 (7-7-22) Just a batch of pictures of how the PWM is wired to the motor. I use quick connect plugs everywhere so I can remove everything easily. The wiring will run under the deck to where the PWC is attached in the cockpit. One set of wires is attached to the “power” side of the PWC and goes to the battery. The other set is from the motor terminals, and goes---guess what!!---to the motor. The motor plugs into a receptacle mounted in the motor well. All of the components come fro Amazon except the extra 10 ga. Duplex wire that I already had. That's the white wire coiled up. I used a ¾ slip elbow and cap on the top of the motor tube to exit the wires. I used hot melt glue to attach it. It is a loose fit. There are several PWC's listed on Amazon. Here's the one I use: ICQUANZX DC Motor Speed Controller, 60A DC10-55V Motor Governor High Power Control Board with Digital Display - 0-100% Adjustable.... I like it because it is in it's own case. The controls fit into holes already in the case except for the RPM counter. I just placed it in the case and don't use it. The plugs are: Miady 5-Pack 12" 10 Gauge 2 Pin Quick Disconnect Audiopipe Polarized Wire Harness, Heavy Duty SAE Connector..... I buy the 5 pack so I'll have more as I need them. You can buy fewer as needed. The motor plug is: Electop SAE Power Socket Sidewall Port, Weatherproof SAE Quick Connect … It comes in a two pack. That's all for now. Time to get on with epoxy coating, sanding, priming, sanding, painting, final assembly. I'll be back when I have more to show y'all. By-the-way. Still planning to get some drawings for ya, so you can build your own. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.