Jump to content

Sign in to follow this  
Designer

Speeding up rigging and unrigging.

Recommended Posts

I have been wanting to do this for a long time to speed up my packing up and unpacking the boat but other jobs had priority. I watched Jay packing up his rig and he inspired me to get it done.

 

I measured the gap between my two masts in their trailing position which turned out to be 1 1/4". The main mast being in the tabernacle puts the track down and head aft. I elect to stow the mizzen mast with the track facing up and head forward. This makes the masts about level athwarts where the crutches need to be for stowing the sprits even though the tracks are on opposite of the mast. This is because the mast diameters are apposite where each of the sprit crutches need to be.

 

I made the crutches out of 3/4" ply and it takes about 3 feet of 1/4" shock cord for each crutch. It takes just seconds to move the loop of shock cord under the masts while gathering the rigging and passing over the top of the sprits and putting the loop into the slot. There is no tendency for the crutch to fall over and the setup is very firm when both shock cords are secured.

 

Like Jay and Chick, I leave all of the lines attached except for what I need to undo to remove the sails. Where I differed is not pulling the sprits up the masts but let my snotters go to the stopper knots. This puts them on the deck making the masts easier to lower.

 

If anyone wants I can email them a pdf of the crutch shapes, they can adjust it to their mast stowage setup. I have not sealed them yet. I will pad the bearing surfaces when they are coated.

sprit crutch.jpg

Sprit crutch.jpg

Share this post


Link to post
Share on other sites

Great idea, Graham. I am dealing with this issue right now with my new BRS 15 mk2.

 

We took it for the first sail yesterday and when rigging down, were able to leave the sails lashed to the masts when laying the masts down. I disconnected the sprit tackle from the masts (snaps), and because of the way I installed the lashing, the sails naturally flaked with a little assistance. I was then able to roll the flaked sail, still lashed to the mast, from the clew up to the mast, then stuff each sail in its own sailbag. These bags then hung down into the hull, mostly, and travelled well at highway speeds. All lines still remained reaved through their blocks, except the sheets and snotter tackles are unsnapped from their sailing positions.

 

I still have the loose ends of lines to deal with, but experience should allow me to clean these up.

2096A78D-8D38-47FA-B27B-1FC3F28A0D1B.jpeg

Share this post


Link to post
Share on other sites

The sail lashing method I used is the fourth from the right in the photo, “Correct” - zig zag lacing. Sails set very well with good downhaul tension. I need to sail her in more varied wind conditions to see how well I like lacing.

CB858DF1-6F4C-4605-A15D-F04C7F5DEA18.jpeg

Share this post


Link to post
Share on other sites

Thanks Graham, I was just padding the crutch Alan built for my CS15, but I like yours with slots for the sprits and ability to keep them attached. Will send email for the .pdf. Rick

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  


Hate ads?
Love messing-about?

Become a Supporting Member - $12 for the next year - and we'll remove the ads for you. Pay by PayPal or credit card.

Give $12 to Support Us




×

Important Information

By using this site, you agree to our Terms of Use.