Jump to content

MikeLTour61

Members
  • Posts

    100
  • Joined

  • Last visited

  • Days Won

    7

MikeLTour61 last won the day on December 12 2016

MikeLTour61 had the most liked content!

About MikeLTour61

  • Birthday 05/25/1961

Profile Information

  • Gender
    Male
  • Location
    Greenville, SC

Recent Profile Visitors

3,629 profile views

MikeLTour61's Achievements

Enthusiast

Enthusiast (6/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

16

Reputation

  1. I think this will be the last update for this thread. I just wanted to thank everyone for helping out this novice boatbuilder... Happy Days is a better boat because of it. After using the boat a few times, I realized that it had some bad characteristics in the ride department. My boat, when loaded with three people - 2 sitting on the drivers seat and one on the front of the console - had a hard time getting out of the hole and up on plane. It eventually made it but it was slow. Once on step, it porpoised and pounded if the boat was moving above 24 mph. It was also hard to maintain one speed as the boat wanted to plow or fly across the water... there was no middle ground - I was always tweaking the throttle. I'm not one to use band-aids to cover up issues but I found something that might help fellow Marissa owners. Not wanting to spend $500+ for trim tabs, I bought a set of Smart Tabs for about $130.00. These are spring-loaded trim tab-looking devices that mount on the transom. They made a huge improvement in all the problem areas mentioned above. I was amazed. If your Marrissa has any of the bad habits that I mention above, you might want to consider the Smart Tabs: http://nauticusinc.com/smart_tabsSX_automatic_trim_tabs.htm
  2. Thanks for the kind words everyone. I don't have any underway pictures because all my picture-takers were on board. Sorry about that. I'll post some performance numbers after the engine is broken in. As of now, it planes at about 4100 RPM and that's where I like to run it. Haven't really run wide open yet. I'll be running mainly on Hartwell and Keowee, Chick.
  3. So it's been quite a while since my last post. I have reduced my to-do list to a few items and went out in the boat twice last weekend. I'm still getting to know the boat and the best way to run but it sure was fun to finally get out there. Here are some pictures of the launching:
  4. Thanks Dale. Latest update: I'm pretty much done with the wiring with the exception of the engine harness. I still need to set up the steering but I need the motor installed to do that. I got the boat on the trailer and the hull painted over the weekend. Did lots of other stuff too. The boat is now ready for the engine and I'm hoping to get it installed this week. Photos:
  5. Thanks Miyot. I can't take credit for the toe kick, I just built the boat from the kit that I bought from Graham. I mostly stuck to the plan and when I modified something, I was very careful. The fire extinguisher box was my idea and I think it was a good one.
  6. Another update... not too much to show since a lot of the work is electrical. I got the cockpit painted except for the sole which will get non-skid. The side decks are finished too.
  7. Latest update: The console is completed and installed. All the large-gauge wire has been run to the switch, main fuse and buss bars. I went with 4 ga. since per my dealer's suggestion. I also ran the engine harness, and steering tubing through the chase. I got the rub rails made and installed. I originally planed and tried to use white oak but it was very hard to bend around the bow curve. Mahogany is softer and seems to bend slightly better so that's what I used. I'll install SS rub rail next winter... I want to go boating now! I'll also make the doors for the console and aft lockers when it's cold out. Since these areas will be closed, I'm not painting them. I got the first coat of primer on all but the cockpit sole and swim platform. I have one more piece to make and install before painting the sole - the seat support. Here's a few pictures:
  8. I was planning on putting the battery in the starboard side aft locker. You don't happen to know the size of the wire used do you?
  9. Thanks for the info Russell! I'm starting work on the electrical system and I'm wondering what size cable the 40 hp Yamaha starter will need. I read in a couple of places where where 4 AWG will suffice but I don't think that's correct... seems small. Thanks, in advance
  10. Thanks for your comments! I thought about doing a dual console with this boat but decided against it since this is the first boat I have built and I didn't have any boatbuilding experience when I started. I think a dual console would work well with this boat except the bow might be a little high... not sure about that yet.
  11. It's been a while since my last update but I've been making good progress. Cockpit deck has been glassed. Fore, side and aft decks have been installed and glassed. As I mentioned earlier, I had to re-make the foredeck pieces due to the angle of my stem being a little low. So far the glassed areas that are still accessible have only one or two coats of epoxy on them. I'll be having an epoxy party one of these days... maybe get some help. Things would go a lot quicker if I didn't have to stop and mix a batch every 15 minutes I got some 5/4 white oak to use on for the rub rails but at 1" it's very hard to bend. Even at 3/4 x 1 it's pretty bad. I don't want to steam bend so I think I'll end up laminating the bendy parts like I did on the inwhale. Center console progressing very well. I have most of the holes cut for the components I'll be installing. I'm using 4 oz. glass on it instead of the 10 oz. I think it will be fine since there's not really any flexing or stress in that area. I'll use 10 oz. tape on the console to deck fillet though. I think I'll hold off on the mahogany dash until next winter. I want to get out and enjoy it this summer and don't want to rush it. It will also give me a chance to decide if I like the dashboard layout. It's really starting to look like a boat, I think. I still have lots to do but I'll bet we'll be boating by July 4th.... Labor day at the latest.
  12. You've built a beautiful boat, that's for sure! How does she go? What horsepower is the engine? If you have pictures of the construction, I'd like to see those too. Mike
  13. Got a few things done over the weekend, mostly on the center console. Finally placed it in the boat to verify it will fit, etc.. pulled it back out to finish work on it. I think I'll complete console glassing and fairing with it out of the boat since it's pretty tight with it installed. I replaced the temporary framing of the console with the permanent yellow pine frame. I put a fire extinguisher box on the side of the port side of the console. I don't know where most people are putting them but I like mine to be very handy. I finally installed the aft decks installed and got the undersides of the side decks epoxied. I'll install those this week, I think. I've decided to put the battery, charger and switch in the port aft locker. Having the battery sitting inches above my gas tank and inches below the fuel filler makes me nervous. I would have liked to put it on the starboard side but the fuel filter will be there too. I want to make maintenance as easy as possible so the port side seemed like the best spot. Russell's boat has what looks like mahogany installed on his dash, instrument panel, front seat and side deck steps. I like the look so I went out and got 30 b.f. of some real nice stuff. That should be plenty to do what I want with some left over. I'm not sure if I'll replace the plywood dash with 3/4" thick solid mahogany or if I should mill the mahogany down to 1/2" and have the 3/8" ply underneath. I can't go thinner than 1/2" on the mahogany because I plan to use 1/4" dowels for joining the separate boards. Russell, if you're listening, do you have any thoughts? Did you fill the grain prior to finishing? It looks nice and shiny.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.