Jump to content

Birth of a New Ravenswood


Pickman

Recommended Posts

Hello all, I have trolled this forum for a short while. I want to share what the SOF community made me do with my winter time. Originally, I was going to build a ceder strip boat with very fancy inlays and interesting woods. I have the skills and the tools but, I knew I would only want to hang it on the wall as a piece of art. I wanted a boat that was light enough for me to portage at least 100 yards if need be. I normally paddle only 3-4 hours at a time. The Ravenswood seems to be just right as to the volume I'll need for day tripping. I'll update how Tattoo preforms when the temps improve here in Mansfield TX. 

 

 

post-3813-0-73376300-1391906590_thumb.jpg

post-3813-0-98155200-1391906674_thumb.jpg

post-3813-0-33304500-1391906758_thumb.jpg.

post-3813-0-21995800-1391906862_thumb.jpg

post-3813-0-51302600-1391907004_thumb.jpg

 

P.S. Thanks for you help with my order Jeff.

Link to comment
Share on other sites


Thanks for the compliments guys. And Mitch you are indeed correct. At first I used then to mock it up because I had a large mess of them i got for free. I found them to be incredibly strong. I compared them to my hand lashing right up to the breaking point of wax sinew and i could get them much tighter. I did a little rescearch and learned to use only US made, 75lb rated, Black for UV resistance and manufactured out of Nylon 66. I know it is an experiment. I covered the hull last so that if they do not work out, I wont have redo the deck paint job. The bout is very strong and stiff. The upside is that two ties would have to break to lose a connection. I keep you updated after further trails.  

Link to comment
Share on other sites

Wow. Thanks Again.  The floor in the front is a cut up $10 camping mat from Academy covered in fake swede. It is removalable and is just to keep my feet warm from the water as i don't wear shoes while in the boat. I strap those muddy things on the deck. Note: The deck rigging is retractable because i don't use it that much and it cuts up the design, that will explain the knotted lines in the cockpit. I just used tung oil on the frame before skinning. Thanks again all. 

Link to comment
Share on other sites

I really like your kayak.  It looks great!  I have a few questions:

1.  I see you don't have a sewn deck seam.  Are the hull and deck stapled to the gunwale?  Is there tape at the hull to deck seam?  What kind of tape?

2.  What fabric did you use?

3.  How did you do the deck graphics?

 

Sorry for all the questions, but I think your beautiful boat will push me to get started on my Ravemswood for which I have all the needed materials.

Link to comment
Share on other sites

Thanks Mr.Douglas, She wont let me hang it on the wall....yet....I have to wait until she wants something....then we compromise.

 

Thank you also Uncler, Glad you like it. As for you questions

 

1. The hull is stapled to the gunnel with stainless staples witch do pull the fabric. I my case all the pulls disappered when I ironed it out and shrunk it. The black stripe covering the seem is vinyl tape over white 1" nylon webbing secured with outdoor carpet tape. It is all temporary because I did not realize it need to be black until after I painted it. The black webbing is on order and will be affixed with 3M automotive double sided tape. Like the stuff that keeps the logos on your car.

2. I used the 8oz poly that Jeff sells. Be sure to add the extra foot Before you place the order. Make his life easier.

3. First cut out a pattern that matches 1/2 of the bow or stern or one whole side. I used taped together construction paper. 

    Second, create a design and cut it out. Next, I taped it to the center line of the topsides and traced it onto the deck with a pencil. I did not un-tape it, I flipped it over to the other side a hit repeat. Lastly, I masked off the design and painted with artist brushes. Tip: Automotive stores carry Frog tape in 1/4" and 1/2" wide rolls. You can follow curves very easily.

 

The last photo shows the wrinkles the staple leave in the cloth. (can't find pointed ss staples) They shrank out completely.

  

Hope this helps 

 

 

 

post-3813-0-08009700-1391986382_thumb.jpg

post-3813-0-32099400-1391986419_thumb.jpg

post-3813-0-51358000-1391986497_thumb.jpg

post-3813-0-78753500-1391986623_thumb.jpg

post-3813-0-96142800-1391986822_thumb.jpg

Link to comment
Share on other sites

Nice job Pickman.  I like your alterations.  I made a cedarstrip kayak and, as you say, I am kind of particular about scratching it up.  I am nearing the end of a curlew build and I am sure I will enjoy it being light weight.  The 17 foot cedar strip ended up being around 60 lb.  Jeff is on to something with his designs.  Congratulations on your new boat - I like the tatoo.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

Supporting Members

Supporting Members can create Clubs, photo Galleries, don't see ads and make messing-about.com possible! Become a Supporting Member - only $12 for the next year. Pay by PayPal or credit card.




×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.