Denis Goyette Posted April 26, 2007 Report Share Posted April 26, 2007 I have been looking around to find the proper 4X4 for my mast but I am out of luck .4X4 Fir is not available where i live and the 4X4 spruce are not kiln dried , I have already purchased some but quick after it started to twist. The only thing I could come with that is 4X4 in the dimension required and kiln dried is Western cedar or eastern cedar. WHAT TO DO??? I thought about laminating 2x4, but it seem so much easier to get the 4x4 and follow the direction from the plan. Your thoughts PLEASE :? Quote Link to comment Share on other sites More sharing options...
normoose Posted April 26, 2007 Report Share Posted April 26, 2007 Hello, I always use 2 - laminated 2x4s with crowns opposing each other and a 1/2"x1/2" groove cut down the middle. This makes a very strong spar. Hope that this helps. Norm :roll: Quote Link to comment Share on other sites More sharing options...
JTam Posted April 26, 2007 Report Share Posted April 26, 2007 Denis, I had to laminate my mast stub because I couldn't get any decent lumber in the 4x4 dimension. I believe the laminated stub is stronger than the a solid piece, and it has none of the stress cracks you often get with the latter not to mention cheaper. For the rest of my mast, I used the bird's mouth method. Quote Link to comment Share on other sites More sharing options...
Denis Goyette Posted April 26, 2007 Author Report Share Posted April 26, 2007 Thanks for the quick reply, great answer, Would Hemlock be any good? Quote Link to comment Share on other sites More sharing options...
ken connors Posted April 26, 2007 Report Share Posted April 26, 2007 http://messing-about.com/forum/viewtopic.php?t=5415 I posted this last week, it might help Quote Link to comment Share on other sites More sharing options...
Pat Mellema Posted April 28, 2007 Report Share Posted April 28, 2007 Denis I used western red cedar for mine and have had no problem with it. It is lighter than the other kinds of wood I could find. I have been out in up to 20 knot winds and it is not a problem. Quote Link to comment Share on other sites More sharing options...
normoose Posted April 28, 2007 Report Share Posted April 28, 2007 Plain old clear spruce 2X4s with 1/2" plywood center is sufficient for such a short mast. Only an opinion but you can take 2 flat but crowned 2X4s and glue them together with crowms opposing each other with a 1/2" plywood center and exceed the strength of a solid spar. --------------------------------- "I am an adventurer by fate, not by choice."- V. V. Gogh Quote Link to comment Share on other sites More sharing options...
normoose Posted April 28, 2007 Report Share Posted April 28, 2007 You can find clear sprue 2 X4s. I have done it and will continue until the mast exceeds...say 16' or so. Saves time and money. These are pocket yachts not deep water cruisers, although each builder has to satify his or her own estetic end results and be safe at the same time. I build these small boats cheaply but when done, I am completely confident and satified with my work and the safety by design. Thanx for your input. Quote Link to comment Share on other sites More sharing options...
normoose Posted April 28, 2007 Report Share Posted April 28, 2007 Two 16' 2X4s are less expensive than a 16' 2X8 every day and I will spend my time scrounging thru the stack of twisted sisters that you find in the pile of 16' 2X4s. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.